An investigation of the performance and stability of zinc oxide thin-film transistors and the role of high-k dielectrics.

Transparent oxide semiconducting films have continued to receive considerable attention, from a fundamental and application-based point of view, primarily because of their useful fundamental properties. Of particular interest is zinc oxide (ZnO), an n-type semiconductor that exhibits excellent optical, electrical, catalytic and gas-sensing properties, and has many applications in various fields. In this work, thin film transistor (TFT) arrays based on ZnO have been prepared by reactive radio frequency (RF) magnetron sputtering. Prior to the TFT fabrication, ZnO layers were sputtered on to glass and silicon substrates, and the deposition parameters optimised for electrical resistivities suitable for TFT applications. The sputtering process was carried out at room temperature with no intentional heating. The aim of this work is to prepare ZnO thin films with stable semiconducting electrical properties to be used as the active channel in TFTs; and to understand the role of intrinsic point defects in device performance and stability. The effect of oxygen (O2) adsorption on TFT device characteristics is also investigated. The structural quality of the material (defect type and concentration), electrical and optical properties (transmission/absorption) of semiconductor materials are usually closely correlated. Using the Vienna ab-initio simulation package (VASP), it is predicted that O2 adsorption may influence film transport properties only within a few atomic layers beneath the adsorption site. These findings were exploited to deposit thin films that are relatively stable in atmospheric ambient with improved TFT applications. TFTs incorporating the optimised layer were fabricated and demonstrated very impressive performance metrics, with effective channel mobilities as high as 30 cm2/V-1s-1, on-off current ratios of 107 and sub-threshold slopes of 0.9 – 3.2 V/dec. These were found to be dependent on film thickness (~15 – 60 nm) and the underlying dielectric (silicon dioxide (SiO2), gadolinium oxide (Gd2O3), yttrium oxide (Y2O3) and hafnium oxide (HfO2)). In this work, prior to sputtering the ZnO layer (using a ZnO target of 99.999 % purity), the sputtering chamber was evacuated to a base pressure ~4 x 10-6 Torr. Oxygen (O2) and argon (Ar) gas (with O2/Ar ratio of varying proportions) were then pumped into the chamber and the deposition process optimised by varying the RF power between 25 and 500 W and the O2/Ar ratio between 0.010 to 0.375. A two-level factorial design technique was implemented to test specific parameter combinations (i.e. RF power and O2/Ar ratio) and then statistical analysis was utilised to map out the responses. The ZnO films were sputtered on glass and silicon substrates for transparency and resistivity measurements, and TFT fabrication respectively. For TFT device fabrication, ZnO films were deposited onto thermally-grown silicon dioxide (SiO2) or a high-k dielectric layer (HfO2, Gd2O3 and Y2O3) deposited by a metal-organic chemical deposition (MOCVD) process. Also, by using ab initio simulation as implemented in the “Vienna ab initio simulation package (VASP)”, the role of oxygen adsorption on the electrical stability of ZnO thin film is also investigated. The results indicate that O2 adsorption on ZnO layers could modify both the electronic density of states in the vicinity of the Fermi level and the band gap of the film. This study is complemented by studying the effects of low temperature annealing in air on the properties of ZnO films. It is speculated that O2 adsorption/desorption at low temperatures (150 – 350 0C) induces variations in the electrical resistance, band gap and Urbach energy of the film, consistent with the trends predicted from DFT results

An investigation of the performance and stability of zinc oxide thin-film transistors and the role of high-k dielectrics

Transparent oxide semiconducting films have continued to receive considerable attention, from a fundamental and application-based point of view, primarily because of their useful fundamental properties. Of particular interest is zinc oxide (ZnO), an n-type semiconductor that exhibits excellent optical, electrical, catalytic and gas-sensing properties, and has many applications in various fields. In this work, thin film transistor (TFT) arrays based on ZnO have been prepared by reactive radio frequency (RF) magnetron sputtering. Prior to the TFT fabrication, ZnO layers were sputtered on to glass and silicon substrates, and the deposition parameters optimised for electrical resistivities suitable for TFT applications. The sputtering process was carried out at room temperature with no intentional heating. The aim of this work is to prepare ZnO thin films with stable semiconducting electrical properties to be used as the active channel in TFTs; and to understand the role of intrinsic point defects in device performance and stability. The effect of oxygen (O2) adsorption on TFT device characteristics is also investigated. The structural quality of the material (defect type and concentration), electrical and optical properties (transmission/absorption) of semiconductor materials are usually closely correlated. Using the Vienna ab-initio simulation package (VASP), it is predicted that O2 adsorption may influence film transport properties only within a few atomic layers beneath the adsorption site. These findings were exploited to deposit thin films that are relatively stable in atmospheric ambient with improved TFT applications. TFTs incorporating the optimised layer were fabricated and demonstrated very impressive performance metrics, with effective channel mobilities as high as 30 cm2/V-1s-1, on-off current ratios of 107 and sub-threshold slopes of 0.9 – 3.2 V/dec. These were found to be dependent on film thickness (~15 – 60 nm) and the underlying dielectric (silicon dioxide (SiO2), gadolinium oxide (Gd2O3), yttrium oxide (Y2O3) and hafnium oxide (HfO2)). In this work, prior to sputtering the ZnO layer (using a ZnO target of 99.999 % purity), the sputtering chamber was evacuated to a base pressure ~4 x 10-6 Torr. Oxygen (O2) and argon (Ar) gas (with O2/Ar ratio of varying proportions) were then pumped into the chamber and the deposition process optimised by varying the RF power between 25 and 500 W and the O2/Ar ratio between 0.010 to 0.375. A two-level factorial design technique was implemented to test specific parameter combinations (i.e. RF power and O2/Ar ratio) and then statistical analysis was utilised to map out the responses. The ZnO films were sputtered on glass and silicon substrates for transparency and resistivity measurements, and TFT fabrication respectively. For TFT device fabrication, ZnO films were deposited onto thermally-grown silicon dioxide (SiO2) or a high-k dielectric layer (HfO2, Gd2O3 and Y2O3) deposited by a metal-organic chemical deposition (MOCVD) process. Also, by using ab initio simulation as implemented in the “Vienna ab initio simulation package (VASP)”, the role of oxygen adsorption on the electrical stability of ZnO thin film is also investigated. The results indicate that O2 adsorption on ZnO layers could modify both the electronic density of states in the vicinity of the Fermi level and the band gap of the film. This study is complemented by studying the effects of low temperature annealing in air on the properties of ZnO films. It is speculated that O2 adsorption/desorption at low temperatures (150 – 350 0C) induces variations in the electrical resistance, band gap and Urbach energy of the film, consistent with the trends predicted from DFT results.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

The impact of multi-layered dielectrics on the electrical performance of ZnO thin-film transistors

The electrical performance of ZnO thin film transistors (TFTs) fabricated on three different dielectric layers is investigated using an inverted staggered bottom gate thin film transistor structure. This work demonstrated the potential of integrating high-k dielectrics in ZnO TFTs in a dielectric multi-layered stack using SiO2 as the support layer for all the hero-dielectrics layers. In order to achieve this, ZnO thin film  semiconducting layers were deposited at room temperature by radio frequency (RF) sputtering method and with no post deposition heat treatment, making them suitable candidates for low cost large area electronics on low temperature substrates (such as plastics). The dielectric films investigated were aluminium nitride (AlN), silicon nitride (SiN) and silicon dioxide (SiO2). The effective mobility of SiN devices was about half that observed in AlN devices. However, the dielectric layers exhibited hysteresis of approximately 0 V, 2 V and 7 V for the SiO2, AlN and SiN respectively. In addition, SiO2 TFTs have lowest threshold voltage (VT) and turn-on voltage (Von). The capacitance-voltage measurement for these device show that the flatband and threshold voltage of SiN and AlN MOS capacitors shifted towards more negative voltages instead when compared with the single layer SiO2 devices

Power sharing enhancement through a decentralized droop-based control strategy in an islanded microgrid

A decentralized intelligent droop-based control strategy is proposed in this paper for the enhancement of equal active and reactive power sharing in an islanded inverter-based microgrid. Droop control is mostly preferred because it does not need communication facilities for its implementation. However, the presence of different feeder impedances for the different distributed generators (DGs) in a microgrid make reactive power sharing inaccurate. Furthermore, as a result of considerable load changes and different droop characteristics for the DGs, the inverter's output voltage and frequency are altered and these in turn alter the reactive and active power sharing respectively. With these conditions, the generalized droop control (GDC) strategy fails to effectively share load reactive and active power among the DGs. In order to extenuate these challenges, this paper presents a nonlinear autoregressive exogenous neural network droop-based control (NARX-NN DBC) strategy which does not depend on the varying line impedances, droop gains for the different DGs and is less affected by fluctuating loads in the grid. A microgrid, made up of two DGs and a load is modelled in MATLAB/Simulink environment and validation of the proposed control strategy is done through many simulations. Within the simulation runtime, NARX-NN DBC yielded a maximum frequency percentage deviation of 0.46% from the nominal value of 50 Hz whereas GDC yielded 0.62%. Regarding the voltage, NARX-NN DBC gave maximum deviation of 0.026% meanwhile GDC gave 0.079% from the nominal value for 380 V. In addition, during 0.57–0.64 s with load active power demand of 4.6 kW, NARX-NN DBC registered 0.43% power sharing error whereas GDC registered 6.5%. On the other hand, during 0.57–0.64 s, with 5kVAr load power demand, NARX-NN DBC registered 0.2% whereas, GDC registered 2%. These obtained results clearly show that NARX-NN DBC strategy has a better performance compared to GDC strategy with respect to power sharing in an autonomous microgrid